|
一、概述
“鑫力”，牌自愈式低电压矿热炉专用电容器采用国际最先进的银一锌一铝复合边缘加厚金属化腊作为材料。引进国际先进设备、技、严格按照国际IEC60831.1：1996标准生产，主要用于矿热炉二次低无功补偿，提高功率因数减少冶炼系统无功功率，降低电耗，提高电端部的冶炼电压，补偿短网的电压降等；为高能耗企业的节能降耗提了新途径，是国家大力推荐使用的节最佳产品。Ⅱ.
|
| Ⅰ. General |
| “Xinli” brand self-healing LV submerged-arc furnace purposed
capacitor adopts the international advanced silver-zn-Al compound
edge thickened metallized film. The company introduces international
advanced equipment and technology, carries out production
strictly according to IEC60831.1: 1996. The products are mainly
applied to secondary LV reactive compensation of submerged-arc
furnace, used to improve the power factor and reduce reactive
power of smelting system, reduce power consumption, increase
smelting voltage, compensate voltage drop of short net; it
provides new ways for energy saving for high energy consumption
enterprise, really is the ideal product responding to the
energy saving recommendation of the government. |
|
| 二、型号说明 |
|
 |
三、主要技术参数
1.使用条件:户内-25℃～+55℃,湿度≤85%RH,海拔≤2000米
2.额定电压:120VAC、150VAC、180VAC、200VAC、230VAC
3.额定容量:1～30Kvar
4.电容允差:0～5%
5.耐压性能:极间2.15Un10s,极壳3000VAC 10s
6.绝缘性能:极壳500VCD 1分钟大于1000MO
7.损耗角正切值:tg￡≤0.1%(工频额定电压,温度20℃)
8.最高允许电压:1.1Un
9.最高允许电流:1.43In
10.自放电特性:切除电网3分钟后,电容器端子间电压降到75V以下
11.符合标准:GB/T12747.1-2004 IEC60831.1:11996 |
Ⅲ.Main technical indexes
1. Service conditions: Indoors –25℃~+55℃, humidity ≤85%RH,
altitude≤2000m
2. Rated voltage: 120VAC, 150VAC, 180VAC, 200VAC, 230VAC
3. Rated capacity: 1~30Kvar
4. Capacitance allowance: 0~5%
5. Resistance to pressure: Pole to pole 2.15Un 10s, pole to
housing 3000VAC 10s
6. Insulation property: Pole to housing 500VDC 1min higher
than 1000MO
7. Loss tangent: tg￡≤0.1% (power frequency rated voltage,
temperature 20℃)
8. Max allowable voltage: 1.1Un
9. Max allowable current: 1.43In
10. Self-discharge characteristic: Voltage among terminals
of capacitor should drop to 75V below after 3min of cutting
off the power grid.
11. In accordance with standards: GB/T12747.1-2004, IEC60831.1:
11996 |
四、主要特点
1.由于采用银锌复合边缘加厚金属化膜作为介质,体积小、重量轻、
性能稳定，
2.损耗低,实际值低于0.1%,所以电容器自身的能耗低,发热小,温升
低,工作寿命长、节能效果佳。
3.优良的自愈性能:过电压所造成介质局部击穿能迅速自愈,恢复正
常工作.使可靠性大为提高.
4.安全性:内装自放电电阻和保险装置,使用安全可靠。
5.不漏油:由于采用特种材料作为浸渍剂,常温呈固态,熔点高于75℃
,在使用中不漏油,避免环境污染。 |
Ⅳ. Main characteristics
1. As it takes silver-zn-Al compound edge thickened metallized
film as medium, it has advantages of compact volume, light
weight, stable performance, etc.
2. Low loss, actual value lower than 0.1%, consequently, the
capacitor itself is featured with low energy consumption,
low heat, low temperature-rise, long service life, favorable
energy saving efficiency.
3. Excellent self-healing property: Partial breakdown of medium
caused by over-voltage can self-heal quickly, and resume normal
operation. This property improves the reliability of product
sharply.
4. Safety: Inner installed with self-discharge resistance
and safety device, it is safe and reliable to operate.
5. Oil tight: It adopts special material as impregnant, it
will be in solid state at normal temperature, melting point
higher than 75℃, oil tight and avoid environmental pollution
during operation. |
五、主要技术指标 MAIN TECHNIQUEINDESSIGN
|
型号及规格
Model & Spec. |
额定电压
Rated voltage （Kv） |
额定容量
Rated capacity
（Kvar） |
额定频率
Rated frequency
（HZ） |
额定电容
Rated capacitance
（uF） |
额定电流
Rated current
（A） |
外形尺寸
Outline size （mm）L*B*H |
图号
Drawing No. |
| BPEMJ0.12-6-1 |
0.12 |
6 |
50 |
1327 |
50 |
215*98*250 |
A |
| BPFMJ0.12-8-1 |
0.12 |
8 |
50 |
1769 |
66.6 |
215*98*250 |
A |
| BPFMJ0.12-10-1 |
0.12 |
10 |
50 |
2211 |
83.3 |
310*125*210 |
B |
| BPFMJ0.12-12-1 |
0.12 |
12 |
50 |
2654 |
100 |
310*125*260 |
B |
| BPFMJ0.15-10-1 |
0.15 |
10 |
50 |
1415 |
66.6 |
215*98*270 |
A |
| BPEMJ0.15-12-1 |
0.15 |
12 |
50 |
1698 |
80 |
215*98*310 |
A |
| BPFMJ0.15-15-1 |
0.15 |
15 |
50 |
2123 |
100 |
310*125*210 |
B |
| BPFMJ0.15-16-1 |
0.18 |
16 |
50 |
2264 |
106.6 |
310*125*230 |
B |
| BPFMJ0.18-10-1 |
0.18 |
10 |
50 |
983 |
55.5 |
215*98*200 |
A |
| BPFM10.18-12-1 |
0.18 |
12 |
50 |
1179 |
66.6 |
215*98*250 |
A |
| BPFMJ0.18-15-1 |
0.18 |
15 |
50 |
1474 |
83.3 |
215*98*310 |
A |
| BPFMJ0.18-16-1 |
0.18 |
16 |
50 |
1572 |
88.8 |
215*98*310 |
A |
| BPFMJ0.18-20-1 |
0.18 |
20 |
50 |
1965 |
111.1 |
310*125*210 |
B |
| BPFMJ0.2-16-1 |
0.2 |
16 |
50 |
1273 |
80 |
215*98*250 |
A |
| BPFMJ0.2-20-1 |
0.2 |
20 |
50 |
1592 |
100 |
215*98*310 |
A |
| BPFMJ0.2-25-1 |
0.2 |
25 |
50 |
1990 |
125 |
310*125*210 |
B |
| BPFMJ0.23-20-1 |
0.23 |
20 |
50 |
1204 |
86.9 |
215*98*250 |
A |
| BPFMJ0.23-25-1 |
0.23 |
25 |
50 |
1505 |
108-7 |
215*98*310 |
A |
| BPFMJ0.23-30-1 |
0.23 |
30 |
50 |
1806 |
130.4 |
310*125*210 |
B |
注：本表格所例的高度不包含接线端子的高度，A、B图型电容器接线端子高度均为55mm
Note: Height listed in this table does not contain the height
of connection terminal, and height of connection terminals
of A and B type capacitors is 55mm. |
|
|
